英语翻译I posted our main purchasing material of galvanized iron

英语翻译
I posted our main purchasing material of galvanized iron wire and steel wire.
1) The spec.of iron wire is below.
For Shipboard Cable.The size is 0.28mm,0.35mm The quantity is up to 3000 ton/year
The tensile strenth is over 35kgf/mm2 .
The elongation is over 12%.
And the surface of galvanized should be smooth.
The zinc coating should be reasonable not to be rust and hot-dip type.
The packing is not fixed maybe 25kg PC Bobbin.
2) The spec.of steel wire is below.
This is for Optic fiber cable.The Main size is 7/1.0,7/1.2,7/1.4,7/1.6.And single size is 1.4,1.6
The quantity is up to 2000ton/year totally.
Zinc coating is 110g/m2,but we can consider less than that.
Our spec.is a little complicated.
I am seeking 1.2mm size of iron wire for drawing.
This is not galvanized but annealed.
1.2mm wire will be drawn as smaller diameter (0.28,0.35)
The wire which has been drawn should meet below our specification in our final process.
Also,I prefer the wire company which is supplier of major shiping cable company.
Final spec.of iron wire (0.28,0.35) is below.
For Shipboard Cable,The size is 0.28mm,0.35mm.The quantity is up to 3000 ton/year
The tensile strength is over 35kgf/mm2 .
The elongation is over 12%.
And the surface of hot dipped galvanized should be smooth.
Here is composite table for wire rod(5.10mm)
Tensile Strength
(Kgf/mm2) Elongation
(%) C Si Mn P S
30~36 30↑ 0.01~0.025↓ 0.03↓ 0.03↓ 0.04↓ 0.04↓
I think that the packing for 1.2mm should be wrapped to protect from water (humidity)
Also,I need some information and quotation about iron wire.
1.What is diameter of rod,metal grade and composite of rod
2.Who is maker of rod?
3.What kind of heat treatment method?(In-line muffle furnace process or not)
4.Pls send me quotation of 1.2mm iron wire which suitable for drawing to 0.28mm iron wire.
5.Pls send me process flow chart from material rod (6mm?) to (1.2mm :annealed not zinc coated) and to (0.28mm annealed and zinc coated )
6.I am attaching company profile card .Please send me that for further business.

我张贴我们的镀锌铁丝,钢丝主要采购材料.
1）规格.在铁丝如下.
对于船用电缆.大小为0.28毫米,0.35微米的量可达3000吨/年
拉伸strenth结束35kgf/mm2.
伸长率超过12％.
而镀锌应该表面光滑.
锌涂层应该是合理不被锈蚀和热浸式.
包装不是固定也许25公斤的PC骨架.
2）规格.钢丝低于.
这是光纤电缆.主要尺寸为7/1.0,7/1.2,7/1.4,7/1.6.和单一的大小是1.4,1.6
的数量达到2000ton/year完全.
锌涂层110g/m2,但我们可以考虑少于.
我们的规范.有点复杂.
我要求1.2mm的铁的拉丝大小.
这不是镀锌,但退火.
1.2mm的电线将以抽签的直径较小（0.28,0.35）
在已制定应满足下面我们对最终的流程规范线.
此外,我更喜欢丝公司是主要的平有线电视公司的供应商.
最终规格.铁丝（0.28,0.35）低于.
对于船用电缆,尺寸0.28毫米,0.35.的数量高达3000吨/年
拉伸强度超过35kgf/mm2.
伸长率超过12％.
以及热浸镀锌表面应光滑.
这里是综合表线材（5.5〜10毫米）
拉伸强度
（Kgf/mm2）伸长率
（％）架C姒呒嗯磷硫
30〜36 30〜0.025↑0.01↓0.03↓0.03↓0.04↓0.04↓
我认为对于1.2mm的包装应包装,以保护水（湿度）
另外,我需要一些信息和铁丝报价.
1.什么是直径棒,金属品位和棒复合?
2.谁是棒制造商?
3.什么样的热处理方法呢?（在线马弗炉过程与否）
4.薪酬水平调查寄给我的1.2mm的铁丝的报价为提请0.28毫米铁丝合适.
5.薪酬水平调查寄给我的材料杆（6毫米?）至（1.2毫米：工艺流程图不是镀锌退火）和（0.28毫米退火和镀锌）
6.我随信附上公司的个人资料卡片.请寄给我,为进一步的业务.
翻译成是这样